If you drive a vehicle powered by the 3.0-liter Hurricane twin-turbo inline-six engine, knowing its correct oil capacity and the right oil to use is essential for performance and long-term reliability.
3.0 Hurricane Engine Oil Capacity
The 3.0 Hurricane engine oil capacity is 7 quarts (6.6 liters) for both the Standard Output and High Output variants using full synthetic 0W-30 oil. Always use oil meeting Chrysler’s MS-13340 specification for best performance and turbocharger protection.
3.0 Hurricane Engine Overview
The 3.0L Hurricane engine is Stellantis’ modern high-performance twin-turbo inline-six designed to replace larger V8 engines while improving fuel efficiency. It comes in two primary variants:
- Standard Output (SO) – around 420 hp
- High Output (HO) – around 510 hp
Both versions operate under high turbocharger temperatures, making oil quality and correct capacity extremely important.
Related Ram TRX Engine Oil Capacity(+Best Recommended Oils)
Best Engine Oils for the 3.0 Hurricane
Click the links Below to Check the Latest Prices on AMAZON
1. Pennzoil Ultra Platinum 0W-30 Full Synthetic
- Meets Chrysler MS-13340
- Excellent turbo protection
- Highly resistant to heat breakdown
- Provides fast cold starts
2. Mobil 1 ESP 0W-30 Full Synthetic
- Designed for high-performance turbo engines
- Low-ash formula protects direct-injection systems
- Excellent anti-wear additives
- Long drain interval capability
3. Valvoline Advanced Full Synthetic 0W-30
- High-temperature stability
- Strong detergents reduce sludge
- Good for severe driving conditions
- Smooth engine performance
Related Ram 1500 Engine Oil Capacity(For All Engine Types)
Recommended Oil Type for the 3.0 Hurricane Engine
The manufacturer recommends:
0W-30 Full Synthetic Oil
This viscosity is necessary due to the engine’s:
- High turbocharger temperatures
- Tight internal tolerances
- Direct injection system
- High power output
Stellantis also specifies that the oil must meet:
Chrysler MS-13340
This is crucial for preventing:
- Turbo bearing wear
- Low-speed pre-ignition (LSPI)
- Sludge buildup
- Viscosity breakdown under heat
Using oil that doesn’t meet this spec can void warranty coverage in some cases.
Related Dodge Charger Engine Swap Compatibility Chart(All Generations)
How Often to Change Oil on the 3.0 Hurricane Engine
Because the Hurricane is a high-output twin-turbo engine, regular oil changes are essential to keep the turbochargers healthy.
Recommended Oil Change Interval:
- Every 5,000–6,000 miles for normal driving
- Every 3,500–4,000 miles for:
- Heavy towing
- High temperatures
- Frequent short trips
- Mountain driving
Dirty oil is the #1 cause of turbo failure, so sticking to shorter intervals is smart.
Signs Your Hurricane Engine Needs an Oil Change
Watch for these warning signs:
- Burnt oil smell
- Louder turbo whistle
- Ticking or tapping sounds on a cold start
- Reduced power under boost
- Dark or gritty oil on the dipstick
Related 4.7 Dodge Engine Oil Capacity(+ Best Recommended Oils)
Why Oil Quality Matters for the 3.0 Hurricane
The 3.0 Hurricane runs extremely hot due to:
- Twin turbochargers
- Direct injection
- High cylinder pressures
This means poor-quality oil can cause:
- Turbo shaft bearing wear
- Carbon buildup on valves
- Early injector failure
- Internal sludge
- Reduced engine life
Using the correct 0W-30 full synthetic with MS-13340 is not optional, it’s critical.
Tips for Maintaining the 3.0 Hurricane Engine
Use only full synthetic 0W-30
Avoid thicker oils like 5W-30 unless specifically advised due to extreme climates.
Always replace the oil filter
A high-efficiency synthetic filter is best for turbo engines.
Warm up before heavy throttle
This allows oil pressure and temperature to stabilize.
Cool down the turbos
Let the engine idle for 30–60 seconds after hard driving.
Stick to short oil intervals
Your turbochargers will thank you.
Related 4.3 Vortec Engine Oil Capacity(+ Best Recommended Oils)
FAQs
How much oil does a 3.0 Hurricane engine take?
The 3.0 Hurricane twin-turbo engine takes 7 quarts (6.6 liters) of full synthetic 0W-30 oil meeting Chrysler MS-13340. This capacity applies to both the Standard Output and High Output versions.
How many quarts of oil does a 3.0 engine take?
Most modern 3.0L engines take 5–7 quarts, depending on design. The 3.0 Hurricane specifically requires 7 quarts, while other 3.0 engines (Ford, Toyota, Mercedes, etc.) may differ.
How much oil does a 3.0 Hilux take?
The Toyota Hilux 3.0 diesel (1KD-FTV) typically takes 7.5 liters (about 7.9 quarts) with a full oil and filter change. Always check your specific model year for exact capacity.
How many liters is a Hurricane engine?
The Hurricane engine is 3.0 liters, referring to the total displacement of the inline-six twin-turbo powerplant used in Jeep Wagoneer, Grand Wagoneer, and select Ram models.
What is the specs of the 3.0 Hurricane engine?
The 3.0 Hurricane comes in two variants:
- Standard Output (SO): ~420 hp, 468 lb-ft torque
- High Output (HO): ~510 hp, 500+ lb-ft torque
- Both feature twin turbochargers, direct injection, aluminum block/heads, and a 7-quart oil capacity.
What oil does a Hurricane engine take?
The Hurricane engine requires 0W-30 full synthetic oil that meets Chrysler MS-13340. This oil provides the high-temperature protection needed for the twin-turbo design.
